Automotive Ethernet enables faster data communication to meet the demands of today’s vehicles and the connected vehicles of the future. QPHY-BroadR-Reach automates testing and validation of 100 Mb/s Automotive Ethernet, which is described in both the BroadR-Reach and 100Base-T1 (IEEE 802.3bw) specifications.
Electrical Telecom Mask Test Package
GRL-USB-PD software provides a simple and efficient way to perform USB-PD electrical parametric and protocol measurements. GRL-USB-PD provides waveform visibility and protocol analysis making it ideal for design and debug of USB Type-C Power Delivery silicon and end products.
GRL-USB-PD-C1 is a flexible test controller, designed for USB-PD Compliance testing of the Unit Under Test (UUT) and more.
The Teledyne LeCroy QPHY-10GBase-KR solution automates testing for 10Gigabite Ethernet Copper Backplane base on the IEEE 802.3ap specifications. The test framework simplifies the test setup and execution of generic and common test requirements such as jitter separation, rise/fall time and transmitter equalization parameters. The guided wizard prompts the user to for specification required patterns and takes the measurements accordingly. The test report includes the test results pass/fail summary, margins and limits, as well as waveforms and measurements used during the test process.
QPHY-10GBASE-T automated compliance test software performs electrical compliance testing of the Physical Media Attachment (PMA) for 10GBASE-T Ethernet PHY, based on IEEE802.3-2008 requirements.
The Teledyne LeCroy QPHY-DDR2 Test Solution is the best way to characterize DDR2 memory interfaces. Capable of performing measurements on 400 MHz, 533 MHz, 667 MHz, 800 MHz, 1066 MHz and custom speed grades, QPHY-DDR2 has a full suite of Clock, Electrical and Timing tests as specified by the JEDEC Specification and Intel JEDEC Specifications Addendums.
The Teledyne LeCroy QPHY-DDR3 Test Solution is the best way to characterize DDR3, DDR3L, and LPDDR3 memory interfaces. Capable of performing measurements on 800 MT/s, 1066 MT/s, 1333 MT/s, 1600 MT/s, 1866 MT/s, 2133 MT/s and custom speed grades, QPHY-DDR3 has a full suite of Clock, Electrical, and Timing tests as specified by the JEDEC Specification.
DDR4 is an evolutionary upgrade from DDR3. It introduces data transfer rates which are nearly double the DDR3 transfer rates, ranging from 1.6 GT/s up to 3.2 GT/s. DDR4's higher transfer rates and lower operating voltage have driven new test methodologies and test requirements which were not previously required for DDR3 in order to ensure proper signal fidelity. QPHY-DDR4 has a full suite of Clock, Electrical, and Timing tests as specified by the JEDEC Specification which will aid in DDR4 design validation.
The QPHY-DisplayPort software option provides an automated test environment for running all of the normative real-time oscilloscope tests for sources in accordance with Version 1.2b of the Video Electronics Standards Association (VESA) DisplayPort PHY Compliance Test Specification, as well as tests for HBR3 signals at 8.1 Gbps.
QPHY-eDP provides a highly automated and easy-to-use solution for Embedded DisplayPort source testing in accordance with version 1.4 of the VESA Embedded DisplayPort PHY compliance test guideline.
Ethernet testing compliant with IEEE 802.3-2005 requires many test setups and connections and mask tests. Using Teledyne LeCroy QualiPHY-ENET these measurements are easy to setup and complete. Instructive connection diagrams and message boxes appear as pop ups on the oscilloscope screen. The connection diagram instructs the user how to change test fixture and jumper pins in order to do complete test. When the tests are complete, QualiPHY will generate a test report in PDF, HTML, or XML formats. Jitter and pulse mask tests are performed with automatic waveform alignment, and all test results feature pass/fail indicators corresponding to the standard being tested.
automated and easy-to-use solution for HDMI transmitter testing in accordance with Version 2.0 of the HDMI Compliance Test Specification (including testing for version 1.4 devices).
The Teledyne LeCroy QPHY-LPDDR2 Test Solution is the best way to characterize LPDDR2 memory interfaces. Capable of performing measurements on 466 MHz, 533 MHz, 667 MHz, 800 MHz, 900 Mhz, 1066 MHz and custom speed grades, QPHY-LPDDR2 has a full suite of Clock, Electrical and Timing tests as specified by the JEDEC Specifications.
QPHY-MIPI-DPHY - D-PHY Compliance Package
Test Solution provides automated control for Teledyne LeCroy oscilloscopes for performing transmitter physical layer tests as described by the MIPI Alliance Specification for D-PHY version 1.00.00
The Teledyne LeCroy QPHY-MOST150 compliance test package provides a highly automated and easy-to-use solution to MOST compliance testing. QPHY-MOST150 will perform all electrical compliance tests as defined in the MOST150 oPHY Automotive Physical Layer Sub-Specification Rev. 1.1 and MOST150 cPHY Automotive Physical Layer Sub-Specification Rev 1.0.
The Teledyne LeCroy QPHY-MOST50 compliance test package provides a highly automated and easy-to-use solution to MOST compliance testing. QPHY-MOST50 will perform all electrical compliance tests as defined in the MOST Electrical Physical Layer Specification Rev. 1.1.
The Teledyne LeCroy QPHY-PCIe Test Solution provides automated control for Teledyne LeCroy oscilloscopes for performing the entire transmitter physical layer tests as described by the Card Electro-mechanical specification Rev 1.1 and 2.0
Teledyne LeCroy QPHY-PCIe3 Test Solution provides automated control for Teledyne LeCroy oscilloscopes for performing transmitter physical layer tests as described by the PCI Express Base Specification Revision 3.0 Version 0.9 and the Card Electromechanical Specification Revision 3.0 Version 0.7.
The Teledyne LeCroy QPHY-SAS2 Test Solution provides automated control for the SDA 8 Zi series of oscilloscopes for performing all of the transmitter physical layer tests as described by version 1.01 of the UNH IOL Serial Attached SCSI (SAS) Consortium SAS-2 6Gb/s Physical Layer Test Suite. This specification covers targets and initiators running at 1.5 Gb/s, 3.0 Gb/s and 6.0 Gb/s.
The QPHY-SAS3 Test Solution provides automated control of the SDA 8 Zi-A and LabMaster 10 Zi oscilloscopes for performing all of the transmitter physical layer tests as described by the T10 SAS-3 specification. This specification covers targets and initiators running at 1.5 Gb/s, 3.0 Gb/s, 6.0 Gb/s, and 12.0 Gb/s.
for SATA compliance testing to be used in conjunction with the PeRT3. By leveraging the capabilities of both the oscilloscope and the PeRT3, QPHY-SATA-TSG-RSG can automatically perform all of the PHY, TSG, OOB, and RSG tests as described by the SATA UTD 1.5. Furthermore, QPHY-SATA-TSG can be configured to test Gen1, Gen2, and Gen3 SATA PUTs.
The Teledyne LeCroy QPHY-SFI solution automates testing for SFI base on the SFF 8431 specifications. The test framework simplifies the test setup and execution of generic and common test requirements such as jitter separation, rise/fall time and transmitter equalization parameters. The guided wizard prompts the user to for specification required patterns and takes the measurements accordingly. The test report includes the test results pass/fail summary, margins and limits, as well as waveforms and measurements used during the test process.
The USB package provides a complete acquisition and analysis system for USB 2.0 devices, hosts, and hubs, as specified in the USB-IF USB 2.0 Electrical Test Specification. The test software implements a full set of electrical tests for USB 2.0, including High-, Full-, and Low-speed tests and is supported by Teledyne LeCroy’s QualiPHY automated test and reporting software.
SuperSpeed USB is one of most highly anticipated standards in several years. At 10x the data rate of USB 2.0 and with new features like CTLE (continuous time linear equalization) and reference channels, SuperSpeed USB will pose new challenges to implementers.
QPHY-USB3.1-Tx-Rx offers an automated test package for USB 3.1 transmitter and receiver compliance testing, characterization, and debug.
The Voyager M310P is Teledyne LeCroy's flagship USB protocol verification system designed for USB 2.0, USB 3.1, Type-C, and USB Power Delivery. Offering the industry's highest fidelity probe design, flexible traffic generation, and a range of turnkey Compliance packages, the Voyager M310P is the most complete platform for cradle-to-grave USB design verification.
The Voyager M310C is Teledyne LeCroy’s USB protocol verification system designed for the latest evolution of universal serial bus, USB Type-C, and includes support for USB Power Delivery. Leveraging Teledyne LeCroy’s extensive expertise in high-speed serial data analysis, the Voyager M310C provides traffic generation and recording of USB 3.1, 3.0 and 2.0 with data rates up to 10 Gb/s.
Teledyne LeCroy’s Advisor T3 is an ultra portable SuperSpeed USB analyzer that delivers market leading accuracy at an extraordinary price. Designed to put precision USB protocol test tools in the hands of every engineer, the Advisor includes all the essential features for SuperSpeed USB debug.
The Teledyne LeCroy Mercury T2C adds USB Type-C and Power Delivery 2.0 & 3.0 support to the industry's smallest and most affordable hardware-based USB 2.0 protocol analyzer. The Mercury T2C combines the de-facto standard CATC Trace display, USB class decoding and Power Delivery 2.0 & 3.0 support in an analyzer that fits in a shirt pocket.
The Mercury T2 is the industry's smallest, most affordable hardware-based USB 2.0 protocol analyzer that combines the defacto standard CATC Trace display with powerful analysis features. The pocket-sized Mercury T2 is bus powered and is controlled using any Windows PC. With comprehensive triggering, the Mercury T2 provides much of the same lab quality protocol analysis capabilities offered in Teledyne LeCroy's top-of-the-line USB analyzers.