Продукция

DA1855A

DA1855A

High-performance 100 MHz Differential Amplifier
DA1855A High-performance 100 MHz Differential Amplifier
DXC100A Selectable 100:1 or 10:1 , Passive Differential Probe Pair
DXC200 50 MHz low capacitance Passive Differential Probe Pair
DXC-5100 100:1, 2.5KV Passive High Voltage Probe Pair
DA101 10:1, 1 MOhm Passive Attenuator
DA1855A-PR2 2 Ch, 100 MHz Differential Amplifier with fast over drive recovery, calibrated offset, and selectable LP filters
DA1855A-PR2-RM Rack mountable version of the DA1855A-PR2
DA1855A-RM DA1855A with rackmount
Differential amplifiers are intended to act as signal conditioning preamplifiers for oscilloscopes and network and spectrum analyzers, providing differential measurement capability to instruments having only a single-ended input. The "-PR2" version of each amplifier is a dual channel unit. The DXC series differential input cables are matched to the characteristics of the amplifier.
Features and Benefits
  • Full control from oscilloscope through ProBus interface
  • DC to 100 MHz bandwidth
  • Outstanding 100,000: 1 Common Mode Rejection Ratio (CMRR)
  • Gain of X1 or X10
  • Industry-leading overdrive recovery
  • Low noise
  • Selectable BW limiting
  • Two gain control modes when connected to a LeCroy oscilloscope
  • Built-in Precision Voltage Generator (PVG)
  • Comparator and true differential offset modes

The DA1855A is a stand-alone, high-performance 100 MHz differential amplifier. It is intended to act as a signal conditioning preamplifier for oscilloscopes, digitizers and spectrum analyzers, providing differential measurement capability to instruments having only a single-ended input. When used with a DA1855A, oscilloscopes can obtain Common Mode Rejection Ratio (CMRR) and overdrive recovery performance levels previously unobtainable.

Amplifier gain can be set to 1 or 10. A built-in input attenuator can be separately set to attenuate signals by a factor of 10, providing gains of 10, 1, or 0.1 and common mode dynamic range of ±15.5 V (÷1) or ±155 V (÷10). Optional probes increase the maximum input signal and common mode ranges in proportion to their attenuation ratio but do not exceed their maximum input voltage rating. Effective gain of the DA1855A, including probe attenuation, amplifier gain and attenuator settings, is automatically displayed.

The DA1855A has a bandwidth of 100 MHz, but any one of the three 3-pole bandwidth limit filters can be selected to reduce bandwidth to 20 MHz, 1 MHz or 100 kHz to limit noise above the frequency of interest.

The DA1855A output is carefully limited to ±500 mV, so that the oscilloscope is not overdriven by large inputs. This allows many oscilloscopes to directly measure the settling of D/A converters with 14-bit (60 ppm) precision, better than any other differential comparator.

The DA1855A features a built-in Precision Voltage Generator (PVG) that can be set to any voltage between ±15.5 V (±10 V in Differential Offset) with up to 100 µV resolution. The PVGs output can be selected as an input to the inverting (-) input of the amplifier for operation as a differential comparator or applied internally as a true differential offset voltage. The PVG is also available for external use through a rear panel connector.

The DA1855A operates from 90 to 250 VAC line without line switching. High-performance differential probes such as the DXC100 ÷10/÷100 high CMRR probes are recommended.

Overdrive Recovery

With a ÷100 probe, the DA1855A settles to within 100 mV referred to input, from a 400 V input signal within 100 ns. With attenuating probes, this allows the in circuit measurement of dynamic saturation in switch mode power converter switching devices.

Comparator Mode

The DA1855A becomes a differential comparator when the internal PVG output is selected as the amplifier's inverting (-) input. In this mode, the DA1855A can be used to very accurately measure relatively small signals that are riding on large AC or DC components. Due to the precision of the voltage generator, an oscilloscope, when used with the DA1855A, can make voltage measurements that are much more accurate than the oscilloscope is capable of by itself. The output of the PVG is available for external use via a rear panel connector.

True Differential Offset Mode

The DA1855A has built-in Precision Voltage Generator can be used to generate a true differential offset while still allowing both inputs to be used as differential inputs. The offset range can be as high as ±50,000 divisions and the generator has 5 1/2 digit resolution. This mode facilitates making measurements such as changes to a transistor's base to emitter voltage caused by variations in temperature and/or current. Used in this mode, the voltage generator can be set to a value that will zero out the static value of the junction's on voltage. The DA1855A's differential measurement capability will reject any dynamic signal common to both sides of the junction, and the oscilloscope is left to measure only the changes in the junction voltage.

Autobalance

Each time either gain setting button is pressed, the DA1855A automatically adjusts the amplifier's DC balance.

Main Specifications
Bandwidth >100 MHz
 
Electrical Characteristics
Risetime (typical) <3.5 ns
 

WaveSurfer 510R
Узнать больше
WaveRunner 8000R
Узнать больше
MDA800A Motor Drive Analyzers
Узнать больше
HDO9000R / HDO9000R-MS
Узнать больше
WaveMaster / SDA 8 Zi-B-R
Узнать больше