Продукция

SDA 806Zi-B-R

SDA 806Zi-B-R

Полоса пропускания 8 ГГц, частота дискретизации 40 ГГц, 4 канала, память 64 MБ, 15.3" сенсорный дисплей, анализатор систем послед. передачи данных,  Входы: 50 Ом и 1 MОм , 6.5 Гбит/с Serial Trigger, декодирование 8b/10b и 64b/66b последовательных сигналов 

Полоса пропускания 4 ГГц, 4 канала, частота дискретизации до 40 ГГц
Полоса пропускания 4 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов 4
Полоса пропускания 6 ГГц, 4 канала, частота дискретизации до 40 ГГц
Полоса пропускания 6 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов 4
Полоса пропускания 8 ГГц, 4 канала, частота дискретизации до 40 ГГц
Полоса пропускания 8 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов 4
Полоса пропускания 13 ГГц, 4 канала, частота дискретизации до 40 ГГц
Полоса пропускания 13 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов 4
Полоса пропускания 16 ГГц, 4 канала, частота дискретизации до 40 ГГц
Полоса пропускания 16 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов 4
Полоса пропускания 20 ГГц, 4 канала, частота дискретизации до 40 ГГц
Полоса пропускания 20 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов 4
Полоса пропускания 25 ГГц, 4 канала, частота дискретизации до 40 ГГц
Полоса пропускания 25 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов "4 (ProLink или ProBus в любых комбинациях до 20 ГГц), 3 (1 в полной полосе, 2 ProLink или ProBus) или 2 в полной полосе"
Полоса пропускания 30 ГГц, 4 канала, частота дискретизации до 40 ГГц
Полоса пропускания 30 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов "4 (ProLink или ProBus в любых комбинациях до 20 ГГц), 3 (1 в полной полосе, 2 ProLink или ProBus) или 2 в полной полосе"
Полоса пропускания 4 ГГц, 4 канала, частота дискретизации 40 ГГц
Полоса пропускания 4 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов "4 (ProLink или ProBus в любых комбинациях до 20 ГГц), 3 (1 в полной полосе, 2 ProLink или ProBus) или 2 в полной полосе""4 (ProLink или ProBus в любых комбинациях до 20 ГГц), 3 (1 в полной полосе, 2 ProLink или ProBus) или 2 в полной полосе"
Полоса пропускания 6 ГГц, 4 канала, частота дискретизации 40 ГГц
Полоса пропускания 6 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов 4 (ProLink или ProBus в любых комбинациях)
Полоса пропускания 8 ГГц, 4 канала, частота дискретизации 40 ГГц
Полоса пропускания 8 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов 4 (ProLink или ProBus в любых комбинациях)
Полоса пропускания 13 ГГц, 4 канала, частота дискретизации 40 ГГц
Полоса пропускания 13 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов 4 (ProLink или ProBus в любых комбинациях)
Полоса пропускания 16 ГГц, 4 канала, частота дискретизации 40 ГГц
Полоса пропускания 16 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов 4 (ProLink или ProBus в любых комбинациях)
Полоса пропускания 20 ГГц, 4 канала, частота дискретизации 40 ГГц
Полоса пропускания 20 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов 4 (ProLink или ProBus в любых комбинациях)
Полоса пропускания 25 ГГц, 4 канала, частота дискретизации 40 ГГц
Полоса пропускания 25 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов "4 (Any combination of 20 GHz ProLink inputs or 3.5 GHz ProBus inputs), 3 (1 @ full BW, 2 with ProLink or ProBus inputs), or 2 (@ full BW)"
Полоса пропускания 30 ГГц, 4 канала, частота дискретизации 40 ГГц
Полоса пропускания 30 ГГц
Частота дискретизации 40 ГГц (80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 20 ГГц с опцией WM8Zi-2X80GS)
Память 256 МБ
Число каналов 4 кан.: 20 ГГц, 2 кан.: 30 ГГц
Сравнить товары

Ключевые особенности:

Полоса пропускания 30 ГГц, частота дискретизации до 80 ГГц            
Самый совершенный пользовательский интерфейс
Запуск по кодовым последовательностям на скоростях до 14,1 Гбит/с
Исключительная достоверность и целостность сигнала
Исчерпывающий набор  инструментов для анализа последовательных данных, отладки, проверки соответствия
Переключаемые входы 50 Ом и 1 МОм (для входов ProLink/ ProBus) во всех моделях для большего удобства в работе – никаких дополнительных адаптеров и внешних усилителей для пробников.
Богатейший набор инструментов измерений, математических функций и ресурсов анализа.
Анализ многоканальных систем последовательной передачи: глазковые диаграммы, комплексное представление джиттера, переходные помехи
Процедуры анализа – предыскажения, коррекция, эмуляция – в реальном времени


Полоса пропускания 30 ГГц, дискретизация 80 ГГц, скорость потока 14,1 ГБ/с. Широкая полоса пропускания и высочайшая производительность среди осциллографов реального времени

Революционное удобство использования

WaveMaster 8Zi-BR - сложный инструмент, разработанный для решения сложных проблем. Благодаря пользовательскому  интерфейсу MAUI, вместе с 15.3 дюймовым сенсорным экраном высокого разрешения, делает расширенный анализ простым в настройке и использовании.

Плоская структура меню включает наиболее распространенные инструменты в простой досягаемости.

Интеллектуальное масштабирование координатной сетки, управление настройками и измерениями позволяет сконцентрироваться на процессе наблюдения и анализа.

Создан для решений

MAUI обеспечивает наиболее тесно интегрированный набор инструментов  в пользовательском интерфейсе осциллографа. Отслеживайте  измеряемые параметры  через полученные графики и их изменения на более длительных временных промежутках, или визуализируйте и оцените их распределения с помощью гистограммы.

Цепь многократных измерений и математических функций вместе с легкостью создавать пользовательские функции анализа для приложений. 

Легкая отладка

Связь проблемы с его первопричиной часто требует анализа сигналов в нескольких областях. WaveMaster 8Zi-B-R позволяет комбинировать разные типы анализа в единый, отображать на дисплее: аналоговые сигналы, декодирование протоколов, глазковые диаграммы, измеренные параметры, и другую информацию в режиме реального времени. 

SDA III – пакет для анализа последовательной передачи данных

Программный пакет TeledyneLeCroy SDAIII-CompleteLinQ для анализа последовательной передачи данных содержит анализ джиттера и мультиканальную глазковую дигамму, режимы сравнения LaneScape™, измерение вертикальных шумов, перекрестных помех и включает в себя современные инструменты анализа. Эти возможности обеспечивают глубокое понимание поведения одно и многоканальной системы последовательной передачи данных.

Последовательные протоколы

Поддержка свыше 19 последовательных протоколов передачи (в т.ч. с возмож- ностью аппаратной синхронизации). Используйте пакет ProtoSync включающий стандарты PCIe, USB, SATA, SAS и Fibre Channel для одновременного наблюдения на дисплее двух представленных состояний (осциллограф-генератор), примечаний декодирования с помощью программного обеспечения анализа протокола. Доступен поиск по данным протокола в таблице и экспорт табличных данных в файл Excel.

Тесты на соответствие стандартам

Программное обеспечение позволяет легко выполнять автоматизированные тесты на соответствие и производить комплексные отчеты испытаний по широкому спектру последовательных стандартов, включая:

  • PCI Express (1.0, 2.0, 3.0)
  • USB1, USB2, USB 3.0
  • DDR2, LPDDR2, DDR3, LPDDR3, DDR4
  • SAS2, SAS3, SATA
  • MIPI D-PHY, MIPI M-PHY
  • 10/100/100 BASE-T, 10GBASE-T, 10GBASE-KR, SFI
  • HDMI 1.4, DisplayPort 1.2
  • MOST50, MOST150, BroadR-Reach

Канал вертикального отклонения

Полоса пропускания 6 ГГц
Аналоговая полоса пропускания 50 Ом (-3 дБ) (ProBus вход) 3,5 ГГц (≥10 мВ/дел)
Аналоговая полоса пропускания 1 МОм (-3 дБ) (ProBus вход) 500 МГц (typical, ≥2 мВ/дел)
Время нарастания (10-90%, 50 Ом) "63 пс (test limit, flatness mode)"
Время нарастания (20-80%, 50 Ом) "47 пс (flatness mode)"
Число каналов 4 (ProLink или ProBus в любых комбинациях)
Ограничение полосы пропускания 20 МГц, 200 МГц, 1 ГГц, 4 ГГц
Входной импеданс "Вход ProLink: 50 Ом ± 2% (≤ 100 мВ/дел), 50 Ом ± 3% (> 100 мВ/дел) Вход ProBus: 50 Ом ± 2%, 1 МОм / 16 пФ (10 МОм / 11 пФ с пробником)"
Входное соединение "вход ProLink - 50 Ом: DC, GND вход ProBus - 1 Mом: AC, DC, GND; 50 Ω: DC, GND"
Максимальное входное напряжение "Вход 2,92 мм: ± 2 Вмакс (≤ 79 мВ/дел), 5,5 Вскз (< 79 мВ/дел) вх. ProLink 50 Ом: ± 2 Вмакс (≤ 100 мВ/дел), 5,5 Вскз (< 100 мВ/дел) вход ProBus 50 Ом: ± 5 Вмакс, 3,5 Вскз вход ProBus 1 МОм: 250 Вмакс (пиковое переменное < 10 кГц + постоянная составляющая)"
Вертикальное разрешение 8 бит (11 бит в режиме увеличения разрешения (ERES))
Погрешность установки коэффициента усиления ± 1,5% (смещение 0 В)

Канал горизонтального отклонения

Временной сдвиг между каналами ± (9 * Кразв.) или макс. 25 нс (большая величина), на канал
Погрешность ОГ ± (1 * 10-6 + 0,5 * 10-6/год)

Система сбора данных

Частота дискретизации "40 ГГц на канал 80 ГГц в 2-х канальном режиме (для осциллографов с полосой пропускания ≤ 25 ГГц с опцией WM8Zi-2X80GS)"
Эквивалентная частота дискретизации " 200 ГГц для периодических сигналов (20 пс/дел … 10 нс/дел) "
Максимальный объем памяти 256 МБ
Память 64 МБ /канал (20 ГГц /32 МБ в двухканальном режиме)

Обработка сигнала

Интерполяция Линейная, Sin x/x

Система синхронизации

Режимы запуска развертки Автоматический, ждущий, однократный, остановка
Источники синхросигнала "Один из каналов, вход внешней синхронизации, от сети, быстрый фронт (от внутреннего генератора перепада 5 МГц) "
Вид входа DC, AC, HFREJ, LFREJ
Предзапуск 0 – 100 % от полной длинны памяти
Послезапуск 0 – 10,000 делений в режиме реального времени
Диапозон установки внешней синхронизации Ext: ±0.4 В, EXT/10: ±4.0 В

Виды синхронизации

Стандартные виды синхронизации "Основная (фронт, длительность импульса, ТВ), интеллектуальная (глич, рант, интервал, окно, скорость нарастания, ожидание, логич. условия, логич. последовательности и пр.), каскадная, по результатам измерений, по последовательным данным в высоко- (опция для WaveMaster) и низкоскоростных потоках"
Опциональные виды синхронизации Не доступно
Опциональные виды синхронизации по протоколам передачи последовательных данных I2C, SPI (SPI, SSPI, SIOP), UART, RS-232, CAN, LIN, FlexRay, MIL-STD-1553, AudioBus, ENET, Ethernet, PCI Express, USB 3.0, USB 2.0, USB2-HSIC, SATA, SAS, FiberChanel, D-PHY, DigRF 3G, MIPI D-PHY, MIPI M-PHY, SENT, ARINC 429, PROTObus MAG

Дисплей

Тип "TFT цветной сенсорный экран, WXGA 1280 х 768 точек, диагональ 39 см, макс. 16 (опция 40) осциллограмм (из каналов, Zoom, памяти, математики)"
Разрешение WXGA 1280 х 768 точек

Процессор

Процессор вид Intel® Core™, 2,6 ГГц
Процессор оперативная память ОЗУ 8 ГБ (опция 16/32 ГБ)
Процессор операционная система Win 7 (64 бит)

Интерфейсы

GPIB Опционально
Ethernet Port 1
USB (Device) 7
Порт для подлкючения внешнего монитора "Полноразмерный соединитель DisplayPort Включает поддержку расширенной настольной работы со вторым монитором."

Пробники

Напряжение "100… 240 В (± 10%), 45… 66 Гц; 100… 120 В (± 10%), 380… 420 Гц (автовыбор)"
Максимальное потребляемое напряжение 975 В / 975 Вт
Размер (ВхШхГ) 355 x 467 x 406 mm
Вес 23,4 кг

Memory Options

DDA8Zi-VL-256
256 Mpt/Ch (4 channel operation) Memory Option for DDA 8 Zi-A. Incl. 16 GB CPU RAM standard
SDA8Zi-VL-256
256 Mpt/Ch (4 channel operation) Memory Option for SDA 8 Zi-A. Incl. 16 GB CPU RAM standard.
SDA8Zi-L-128
128 Mpt/Ch (4 channel operation) Memory Option for SDA 8 Zi-A. Incl. 16 GB CPU RAM standard.
DDA8Zi-M-64
64 Mpt/Ch (4 channel operation) Memory Option for DDA 8 Zi-A.
SDA8Zi-M-64
64 Mpt/Ch (4 channel operation) Memory Option for SDA 8 Zi-A.
WM8Zi-VL-256
256 Mpts/Ch Memory Option for WaveMaster 8 Zi. SDA 8 Zi, and DDA 8 Zi. Includes an additional 4 GB of RAM (8 GB total)
WM8Zi-L-128
128 Mpt/Ch (4 channel operation) Memory Option for WaveMaster 8 Zi-A. Incl. 16 GB CPU RAM standard.
WM8Zi-M-64
64 Mpts/Ch Memory Option for WaveMaster 8 Zi. SDA 8 Zi, and DDA 8 Zi. Includes an additional 4 GB of RAM (8 GB total)
WM8Zi-S-32
32 Mpts/Ch Memory Option for WaveMaster 8 Zi. SDA 8 Zi, and DDA 8 Zi. Includes 4 GB RAM standard

Miscellaneous

TTL-AUX-OUT
Accessory for Zi oscilloscopes to enable TTL level output from the Aux Out connector
20dB-SMA-Attenuator
20 dB Attenuator
Zi-FrontPanel
Removable front panel for WavePro 7Zi and WaveMaster 8Zi Oscilloscopes
KYBD-1
Keyboard
Rise-Time-Filter-100ps
Low-Pass Rise Time Filter 100 ps
Rise-Time-Filter-150ps
Low-Pass Rise Time Filter 150 ps
OC910
Deluxe LabMaster Mobile Cart
RACKMOUNT
Rack Mount Accessory
OC1024-A
Deluxe oscilloscope cart with one tiltable shelf and additional storage
OC1021-A
Basic oscilloscope cart with one tiltable shelf

Mixed Signal Accessories

HDA-DLS-09QL
9 channel QuickLink leadset for HDA125
HDA-DLS-18QL
18 channel QuickLink leadset for HDA125
MSO-DLS-36
Digital Lead Set, D18-D35
MSO-DLS-18
Digital Lead Set, D0-D17
MSO-3M
3M Interconnect Cable, D0-D17 or D18-D35
MSO-MICTOR
Mictor Cable, D0-D35
PK400-3
Small gripper probe set for 0.008'' (0.2 mm) pin pitch, includes 10 probes with color-coded leads
PK400-2
Medium gripper probe set for 0.04'' (1.0 mm) pin pitch, includes 10 probes with color-coded leads
PK400-1
Large gripper probe set for 0.10'' (2.54 mm) pin pitch, includes 10 probes with color-coded leads
PK400-0
Extra Large Gripper Probe Set . Includes 22 probes

Synchronize Oscilloscope Options

Zi-8CH-SYNCH
HW Kit to allow combination of channels from two Zi or Zi-A oscilloscopes. Allows combination of all channels from two oscilloscopes (8 channels total) or combination of all 20-30 GHz channels from two 20-30 GHz 8Zi or 8Zi-A oscilloscopes (4 channels total), or combination of 45 GHz channels

Remote Control/Network Options

GPIB-4
GPIB option for WaveMaster 8Zi-B oscilloscope

Sampling Rate Options

WM8Zi-2X80GS
80 GS/s on 2ch Sampling Rate Option for WaveMaster/SDA/DDA 8 Zi and 8Zi-A (not available for 820Zi, 825Zi/Zi-A, 830Zi/Zi-A, 9x30Zi-A, 845Zi-A or 9x45Zi-A). Includes two separate external interleaving devices with storage case.

Computer Upgrade

WM8Zi-8-UPG-32GBRAM
8 GB to 32 GB CPU RAM Upgrade Option
WM8Zi-500GB-RHD-02
Additional 500 GB Hard Drive for WM8Zi or 8Zi-A. Includes Windows 7 OS, LeCroy oscilloscope software and critical scope operational file duplicates.
WM8Zi-500GB-HD
Upgrade from standard size hard drive to 500 GB hard drive

Serial Data Test Fixtures

TF-USB3
SuperSpeed and SuperSpeedPlus USB Test Fixtures
TF-10GBASE-T
Test Fixture for 10GBase-T
TF-MIPI-MPHY-DUALPAK
MIPI M-PHY input offset adapter dual pack
TF-SATA-C-Kit
SATA Compliance Test Kit
TF-HDMI-3.3V-QUADPAK
HDMI Pull-Up Terminator Quad Pack - For Use with the Wilder-Tech HDMI-TPA-P Plug Test Adapter
TF-USB-B
USB 2.0 Compliance Test Fixture

Serial Trigger Hardware

WM8Zi-14GBIT-80B-SYMBOL-TD
80-bit NRZ, 8b/10b, and 64b/66b 14.1 Gbps Serial Trigger option for WaveMaster 8 Zi-A and DDA 8 Zi-A

Mixed Signal Solutions

MS-250
250 MHz Maximum Input Frequency, 18 Channels, 10 Mpts/ch Mixed Signal Oscilloscope Option
MS-500-36
250 MHz Maximum Input Frequency, 36 Channels, 25 Mpts/ch Mixed Signal Oscilloscope Option
MS-500
500 MHz Maximum Input Frequency, 18 Channels, 50 Mpts/ch Mixed Signal Oscilloscope Option
HDA125-09-LBUS
12.5 GS/s High-speed Digital Analyzer with 9ch QuickLink leadset and LBUS connection
HDA125-18-LBUS
12.5 GS/s High-speed Digital Analyzer with 18ch QuickLink leadset and SYNC connection

Data Storage Software

DDM2
Disk Drive Analyzer Software Package
DDA
Disk Drive Analyzer Software Package
AORM
Advanced Optical Recording Measurements

Other Software Options

VectorLinQ VSA Package
Signal Analysis (VSA) options provide an extensive toolset for demodulation and analysis of RF and IQ modulated signals. These tools provide deep insight into advanced signal types with maximum measurement flexibility and sophisticated signal visualization. The intuitive user interface is easy to set up and allows for user customization to meet the needs of even the most complex signals.
Spectrum Analyzer Option
Spectrum analyzer style user interface with controls for start/stop frequency or center frequency and span. Utilize up to 20 markers to automatically identify harmonics and quickly analyze frequency content. Monitor how the spectrum changes over time by viewing the spectrogram in 2D or 3D.
Optical-LinQ
The world leading OpticalLinQ software for analysis of optically modulated signals can now be used with any coherent optical receiver (including the Teledyne LeCroy IQS series of receivers). Users can select a wide variety of analysis views and parametric measurements to gain a complete understanding of their optical signal path.
EMC
Understanding an electronic design's susceptibility to Electronmagnetic (EM) discharge is an important element of validation. Whether fast one time event transients or repetitive bursts EM can introduce unexpected events in the circuit performance. Teledyne LeCroy Oscilloscopes offer high sample rates and measurements tailored specifically to this task. Whether one pulse or billions of measurements engineers gain insight into their device and system suseptibility.

Serial Data Analysis

VirtualProbe
By using VirtualProbe, you can understand the characteristics of signals where a physical probe cannot be placed, such as inside of a package or at the end of an interconnect that doesn't physically exist. You can choose to remove effects caused by elements such as fixtures that are not be present in a production configuration, and also add the effects of a device that is to be included but for which only an S-parameter model exists. Use in conjunction with SDAIII products to complete your serial data analysis solution set.
SDM
Serial Data Mask Package
PAM4
PAM4 signaling represents a new step in the evolution of serial data signal formats, overcoming some fundamental limitations of traditional NRZ signaling. But with new signal types come new measurement needs. Teledyne LeCroy’s PAM4 analysis package meets these needs by leveraging industry-leading eye, jitter and noise analysis capabilities to perform eye, jitter and noise analysis of PAM4 signals.
Eye Doctor II
Eye Doctor II provides the channel emulation and de-embedding tools that engineers need for the next generation of serial data standards
CBL-DE-EMBED
Remove cable effects from your measurements
SDAIII-CompleteLinQ
signaling, designers of serial data systems require multi-lane analysis. Unleash the power of multi-lane SDA analysis to perform eye and jitter measurements on up to four lanes, simultaneously.

Serial Data Compliance

QPHY-USB3.1-Tx-Rx
QPHY-USB3.1-Tx-Rx offers an automated test package for USB 3.1 transmitter and receiver compliance testing, characterization, and debug.
QPHY-USB3-Tx-Rx
SuperSpeed USB is one of most highly anticipated standards in several years. At 10x the data rate of USB 2.0 and with new features like CTLE (continuous time linear equalization) and reference channels, SuperSpeed USB will pose new challenges to implementers.
QPHY-USB
The USB package provides a complete acquisition and analysis system for USB 2.0 devices, hosts, and hubs, as specified in the USB-IF USB 2.0 Electrical Test Specification. The test software implements a full set of electrical tests for USB 2.0, including High-, Full-, and Low-speed tests and is supported by Teledyne LeCroy’s QualiPHY automated test and reporting software.
QPHY-SFI
The Teledyne LeCroy QPHY-SFI solution automates testing for SFI base on the SFF 8431 specifications. The test framework simplifies the test setup and execution of generic and common test requirements such as jitter separation, rise/fall time and transmitter equalization parameters. The guided wizard prompts the user to for specification required patterns and takes the measurements accordingly. The test report includes the test results pass/fail summary, margins and limits, as well as waveforms and measurements used during the test process.
QPHY-SATA-TSG-RSG
for SATA compliance testing to be used in conjunction with the PeRT3. By leveraging the capabilities of both the oscilloscope and the PeRT3, QPHY-SATA-TSG-RSG can automatically perform all of the PHY, TSG, OOB, and RSG tests as described by the SATA UTD 1.5. Furthermore, QPHY-SATA-TSG can be configured to test Gen1, Gen2, and Gen3 SATA PUTs.
QPHY-SAS2
The Teledyne LeCroy QPHY-SAS2 Test Solution provides automated control for the SDA 8 Zi series of oscilloscopes for performing all of the transmitter physical layer tests as described by version 1.01 of the UNH IOL Serial Attached SCSI (SAS) Consortium SAS-2 6Gb/s Physical Layer Test Suite. This specification covers targets and initiators running at 1.5 Gb/s, 3.0 Gb/s and 6.0 Gb/s.
QPHY-PCIe3
Teledyne LeCroy QPHY-PCIe3 Test Solution provides automated control for Teledyne LeCroy oscilloscopes for performing transmitter physical layer tests as described by the PCI Express Base Specification Revision 3.0 Version 0.9 and the Card Electromechanical Specification Revision 3.0 Version 0.7.
QPHY-PCIe
The Teledyne LeCroy QPHY-PCIe Test Solution provides automated control for Teledyne LeCroy oscilloscopes for performing the entire transmitter physical layer tests as described by the Card Electro-mechanical specification Rev 1.1 and 2.0
QPHY-MOST50
The Teledyne LeCroy QPHY-MOST50 compliance test package provides a highly automated and easy-to-use solution to MOST compliance testing. QPHY-MOST50 will perform all electrical compliance tests as defined in the MOST Electrical Physical Layer Specification Rev. 1.1.
QPHY-MOST150
The Teledyne LeCroy QPHY-MOST150 compliance test package provides a highly automated and easy-to-use solution to MOST compliance testing. QPHY-MOST150 will perform all electrical compliance tests as defined in the MOST150 oPHY Automotive Physical Layer Sub-Specification Rev. 1.1 and MOST150 cPHY Automotive Physical Layer Sub-Specification Rev 1.0.
QPHY-MIPI-MPHY
The QPHY-MIPI-MPHY Test Solution provides automated control of Teledyne LeCroy oscilloscopes for performing transmitter physical layer tests as described by the MIPI Alliance Specification for M-PHY version 3.0.
QPHY-MIPI-DPHY - D-PHY Compliance Package
Test Solution provides automated control for Teledyne LeCroy oscilloscopes for performing transmitter physical layer tests as described by the MIPI Alliance Specification for D-PHY version 1.00.00
QPHY-LPDDR2
The Teledyne LeCroy QPHY-LPDDR2 Test Solution is the best way to characterize LPDDR2 memory interfaces. Capable of performing measurements on 466 MHz, 533 MHz, 667 MHz, 800 MHz, 900 Mhz, 1066 MHz and custom speed grades, QPHY-LPDDR2 has a full suite of Clock, Electrical and Timing tests as specified by the JEDEC Specifications.
QPHY-HDMI2
automated and easy-to-use solution for HDMI transmitter testing in accordance with Version 2.0 of the HDMI Compliance Test Specification (including testing for version 1.4 devices).
QPHY-ENET
Ethernet testing compliant with IEEE 802.3-2005 requires many test setups and connections and mask tests. Using Teledyne LeCroy QualiPHY-ENET these measurements are easy to setup and complete. Instructive connection diagrams and message boxes appear as pop ups on the oscilloscope screen. The connection diagram instructs the user how to change test fixture and jumper pins in order to do complete test. When the tests are complete, QualiPHY will generate a test report in PDF, HTML, or XML formats. Jitter and pulse mask tests are performed with automatic waveform alignment, and all test results feature pass/fail indicators corresponding to the standard being tested.
QPHY-eDP
QPHY-eDP provides a highly automated and easy-to-use solution for Embedded DisplayPort source testing in accordance with version 1.4 of the VESA Embedded DisplayPort PHY compliance test guideline.
QPHY-DisplayPort
The QPHY-DisplayPort software option provides an automated test environment for running all of the normative real-time oscilloscope tests for sources in accordance with Version 1.2b of the Video Electronics Standards Association (VESA) DisplayPort PHY Compliance Test Specification, as well as tests for HBR3 signals at 8.1 Gbps.
QPHY-DDR4
DDR4 is an evolutionary upgrade from DDR3. It introduces data transfer rates which are nearly double the DDR3 transfer rates, ranging from 1.6 GT/s up to 3.2 GT/s. DDR4's higher transfer rates and lower operating voltage have driven new test methodologies and test requirements which were not previously required for DDR3 in order to ensure proper signal fidelity. QPHY-DDR4 has a full suite of Clock, Electrical, and Timing tests as specified by the JEDEC Specification which will aid in DDR4 design validation.
QPHY-DDR3
The Teledyne LeCroy QPHY-DDR3 Test Solution is the best way to characterize DDR3, DDR3L, and LPDDR3 memory interfaces. Capable of performing measurements on 800 MT/s, 1066 MT/s, 1333 MT/s, 1600 MT/s, 1866 MT/s, 2133 MT/s and custom speed grades, QPHY-DDR3 has a full suite of Clock, Electrical, and Timing tests as specified by the JEDEC Specification.
QPHY-DDR2
The Teledyne LeCroy QPHY-DDR2 Test Solution is the best way to characterize DDR2 memory interfaces. Capable of performing measurements on 400 MHz, 533 MHz, 667 MHz, 800 MHz, 1066 MHz and custom speed grades, QPHY-DDR2 has a full suite of Clock, Electrical and Timing tests as specified by the JEDEC Specification and Intel JEDEC Specifications Addendums.
QPHY-10GBASE-T
QPHY-10GBASE-T automated compliance test software performs electrical compliance testing of the Physical Media Attachment (PMA) for 10GBASE-T Ethernet PHY, based on IEEE802.3-2008 requirements.
QPHY-10GBase-KR
The Teledyne LeCroy QPHY-10GBase-KR solution automates testing for 10Gigabite Ethernet Copper Backplane base on the IEEE 802.3ap specifications. The test framework simplifies the test setup and execution of generic and common test requirements such as jitter separation, rise/fall time and transmitter equalization parameters. The guided wizard prompts the user to for specification required patterns and takes the measurements accordingly. The test report includes the test results pass/fail summary, margins and limits, as well as waveforms and measurements used during the test process.
GRL-USB-PD-C1
GRL-USB-PD-C1 is a flexible test controller, designed for USB-PD Compliance testing of the Unit Under Test (UUT) and more.
GRL-USB-PD
GRL-USB-PD software provides a simple and efficient way to perform USB-PD electrical parametric and protocol measurements. GRL-USB-PD provides waveform visibility and protocol analysis making it ideal for design and debug of USB Type-C Power Delivery silicon and end products.
DDR Debug Toolkit
The DDR Debug Toolkit provides test, debug and analysis tools for the entire DDR design cycle. The unique DDR analysis capabilities provide automatic Read and Write burst separation, bursted data jitter analysis and DDR-specific measurement parameters.
QPHY-BroadR-Reach
Automotive Ethernet enables faster data communication to meet the demands of today’s vehicles and the connected vehicles of the future. QPHY-BroadR-Reach automates testing and validation of 100 Mb/s Automotive Ethernet, which is described in both the BroadR-Reach and 100Base-T1 (IEEE 802.3bw) specifications.

Digital Filtering Software

DFP2
Digital Fiter Package

Jitter Analysis Software

JITKIT
Validating system jitter performance and analyzing systems with high jitter levels comprises a significant portion of a system engineer's test and validation time. JITKIT makes it simple and easy to understand the basic system jitter performance of clock signals and clock-data activities, including period, half period, cyclecycle, skew, amplitude, differential voltage crossing, slew rate, and a wide variety of other common jitter measurements.

Power Analysis Software

Power Analyzer Package
Automatically and accurately analyze the performance of switched-mode power circuits

Serial Trigger and Decode

USB2bus TD
performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.
USB2-HSICbus D
The comprehensive and intuitive deocde and easy to navigate table display enable a powerful toolset to quickly debug a USB 2.0 HSIC powered system. Combine it with ProtoSync to get a full view of all the USB 2.0 layers.
UNIPRObus D
The MIPI UniPro Protocol Decoder analyzes acquired M-PHY analog waveforms and provides insight into multiple levels of UniPro protocol information. Data and Control frames are presented in an intuitive table format, where selecting a frame expands its content to a color-coded symbolic level, simultaneously creating a zoom. Decode annotation information is displayed on the physical layer waveform for a quick reference.
UART-RS232bus TDME
The UART and RS-232 Trigger Decode (TD) and Trigger, Decode, Measure/Graph and Physical Layer (TDME) solutions both provide high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities. The TDME option also provides Measure/Graph (M) capability with automated measurement and graphing tools and Eye Diagram (E) capability for physical layer signal assessment and debug.
UART-RS232bus TD
The UART and RS-232 Trigger Decode solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.
SPMI Decode
The MIPI System Power Management Interface (SPMI) decoder provides a fast and easy way to understand and correlate SPMI bus traffic to DC power rails and power management IC (PMIC) operations in mobile, handheld, and battery-powered embedded systems.
SPIbus TDME
The SPI Trigger, Decode, Measure/Graph and Physical Layer (TDME) solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities. The TDME option also provides Measure/Graph (M) capability with automated measurement and graphing tools and Eye Diagram (E) capability for physical layer signal assessment and debug.
SPIbus TD
The SPI Trigger solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.
SpaceWirebus D
The SpaceWire decode adds a unique set of tools to your Teledyne LeCroy oscilloscope that simplifies the design, debug, and maintenance of SpaceWire systems. The high speed SpaceWire data stream is annotated directly on the physical layer waveforms. Various sections of the protocol are color-coded to make it easy to understand the protocol traffic. The decoder provides an interactive table, search, and zoom to make debugging fast and effective.
SENTbus D
High-resolution SENT sensor and ECU message frames are intuitively decoded on the waveform, provided in an interactive table, and payload content search tools make debugging fast and effective.
SATA Trigger and Decode
The SATAbus TD option provides comprehensive SATA 1.5 and 3 Gb/s protocol triggering in a WaveRunner 6 Zi oscilloscope using a true hardware protocol trigger for most efficient debug.
SAS bus D
The SASbus D decode annotation option is available for most Teledyne LeCroy oscilloscopes. It permits link and data layer decoding of 1.5, 3, 6, or 12 Gb/s SAS physical layer signals. Decode information is annotated on the physical layer waveform. Various sections of the protocol are color-coded to make it easy to understand the protocol traffic.
ProtoSync
The ProtoSync option further leverages the supported Teledyne LeCroy decode annotation options (PCIEbus D, USB3bus D, USB2bus D, USB2 HSICbus D, SATAbus D, SASbus D, FCbus D) installed on the oscilloscope.
PCIe Decode
The PCIEbus D option provides comprehensive PCI Express Gen1.x protocol decode for most efficient debug.
Manchester Decode
Manchester coding is a line code in which the encoding of each data bit has at least one transition and 1s and 0s have equal bit width and therefore has no DC component. Manchester signals are self-clocking, which means that a clock signal can be recovered from the encoded data. Manchester Configurable protocol decoder enables grouping bits using various combinations of bit rate, polarity, idle condition, time out and more to decipherable messages. It allows decode of various protocols developed using Manchester encoding scheme.
M-PHYbus DP - Decode and Physical layer test option
The MIPI M-PHY and D-PHY Decode and Physical Layer Test is the ideal tool for powerful system level protocol debug as well as problem solving for signal quality issues. The D-PHY decode solution adds a unique set of tools to your oscilloscope, simplifying how you design and debug MIPI D-PHY, CSI-2 and DSI signals.
M-PHYbus D - Decode option
The MIPI M-PHY and D-PHY Decode and Physical Layer Test is the ideal tool for powerful system level protocol debug as well as problem solving for signal quality issues. The D-PHY decode solution adds a unique set of tools to your oscilloscope, simplifying how you design and debug MIPI D-PHY, CSI-2 and DSI signals.
LINbus TDME
The LIN Trigger Decode (TD) and Trigger, Decode, Measure/Graph and Physical Layer (TDME) solutions both provide high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities. The TDME option also provides Measure/Graph (M) capability with automated measurement and graphing tools and Eye Diagram (E) capability for physical layer signal assessment and debug.
LINbus TD
The LIN Trigger Decode (TD) solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.
I2Cbus TDME
The I2C Trigger, Decode, Measure/Graph and Physical Layer (TDME) solution provides high performance triggers, transparent color-coded decode overlays, protocol tables, and search capabilities, Measure/Graph capability with automated measurement and graphing tools, and Eye Diagram capability for physical layer signal assessment and debug.
I2Cbus TD
The I2C Trigger Decode (TD) solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.
FlexRaybus TD
The FlexRay Trigger Decode (TD) solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.
Fibre Channel Decode
The FCbus D decode annotation option is available for most Teledyne LeCroy oscilloscopes. It permits link and data layer decoding of 1, 2, 4, or 8GFC (1.0625 Gb/s to 8.5 Gb/s) Fibre Channel physical layer signals.
Ethernet Decode
Ethernet Decode Ethernet decoding provides protocol awareness to the oscilloscope for fast debugging.
Embedded System Bundle TD
The Embedded Bundle Trigger and Decode (TD) contains the capabilities included in the I2Cbus, SPIbus, and UART-RS232bus TD products. For more information on this product, please see the product pages for I2Cbus TD, SPIbus TD, and UART-RS232bus TD.
DigRF v4 bus
The DigRF 3G and v4 decode are the ideal tools for powerful system level protocol debug as well as problem solving for signal quality issues. The DigRF decodes add a unique set of tools to your oscilloscope, simplifying how you design and debug MIPI digital RF systems.
DigRF 3G bus
The DigRF 3G decode is the ideal tool for powerful system level protocol debug as well as problem solving for signal quality issues. The DigRF 3G decode adds a unique set of tools to your oscilloscope, simplifying how you design and debug MIPI digital RF systems.
D-PHYbus DP - Decode and Physical layer test option
The MIPI M-PHY and D-PHY Decode and Physical Layer Test is the ideal tool for powerful system level protocol debug as well as problem solving for signal quality issues. The D-PHY decode solution adds a unique set of tools to your oscilloscope, simplifying how you design and debug MIPI D-PHY, CSI-2 and DSI signals.
CANbus TDME Symbolic
The CAN Trigger, Decode, Measure/Graph and Eye Diagram solution with Symbolic CAN support (TDME Symbolic) provides high performance triggers, transparent color-coded decode overlays, protocol tables, and search capabilities, Measure/Graph (M) capability with automated measurement and graphing tools, and Eye Diagram (E) capability for physical layer signal assessment and debug. Symbolic DBC files may be used to set up the trigger, display symbolic decodes, and select parameters for serial digital data extraction to an analog value
CANbus TDME
The CAN Trigger, Decode, Measure/Graph and Eye Diagram (TDME) solution provides high performance triggers, transparent color-coded decode overlays, protocol tables, and search capabilities, Measure/Graph (M) capability with automated measurement and graphing tools, and Eye Diagram (E) capability for physical layer signal assessment and debug.
CANbus TD
performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.
CAN FDbus TDME Symbolic
The CAN FD Trigger, Decode, Measure/Graph and Eye Diagram solution with Symbolic support (TDME Symbolic) provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities, Measure/Graph (M) capability with automated measurement and graphing tools, and Eye Diagram (E) capability for physical layer signal assessment and debug for both CAN and CAN FD. Symbolic DBC files may be used to set up the trigger, display symbolic decodes, and select parameters for serial digital data extraction to an analog value.
CAN FDbus TDME
The CAN FD Trigger, Decode, Measure/Graph and Eye Diagram (TDME) solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities, Measure/Graph (M) capability with automated measurement and graphing tools, and Eye Diagram (E) capability for physical layer signal assessment and debug for both CAN and CAN FD. Symbolic DBC files may be used to set up the trigger, display symbolic decodes, and select parameters for serial digital data extraction to an analog value.
CAN FDbus TD
The CAN FD Trigger Decode (TD) solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities for both CAN and CAN FD.
8B10B
8b10b Decode Option
64b/66b Symbol Decode
64b/66b Symbol Decode provides protocol awareness to your oscilloscope physical layer tool
1553 TDME
The MIL-STD-1553 Trigger Decode solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.
1553 TD
The MIL-STD-1553 Trigger Decode solution provides high performance triggers and transparent color-coded decode overlays, protocol tables, and search capabilities.
10-Gigabit Ethernet Decode
The 10-Gigabit Ethernet decode option for Teledyne LeCroy oscilloscopes provides link layer decode information annotated on the 10-Gigabit physical layer waveform. This provides the ability to view protocol traffic on the oscilloscope. It also aids in debugging problems that are not solely analog or digital in nature - issues not evident with a Protocol Analyzer
MDIO Decode
The Media Data Input/Output (MDIO) decoder provides a fast and easy way to understand and correlate MDIO bus traffic to the management of PHYs or physical layer devices in media access controllers (MACs).
AudioBus - I2S
Teledyne LeCroy’s Serial AudioBus trigger, decode, and graph package provides all the tools needed to properly analyze and debug digital audio buses. Teledyne LeCroy’s solution addresses the I2S, LJ, RJ, and TDM variations of the audio bus standard.
ARINC429bus DSymbolic
The ARINC 429 Decode (D) option provides Symbolic decode with transparent color-coded decode overlays, protocol tables, and search capabilities.

MDIO Decode

6GBIT-80B-SYMBOL-TD
Rapidly pinpoint and debug problems with NRZ, 8b/10b and 64b/66b signals using the high-speed serial trigger and decode options. Hardware trigger products with maximum bitrates of 6.5 and 14.1 Gbps are available for WaveMaster 8 Zi-A, LabMaster 9 Zi-A and LabMaster 10 Zi series oscilloscopes, and include 8b/10b and 64b/66b decoders.

High Speed Output Accessories

LSIB-CABLE-7M
PCI Express x 4 7-meter cable with x4 cable connectors include
LSIB-CABLE-3M
PCI Express x 4 3-meter cable with x4 cable connectors included
LSIB-HOSTCARD
PCI Express x4 Express Card Host Interface for laptop Express Card slot
LSIB-HOSTBOARD
PCI Express x4 Host Interface Board for desktop PC

Probe Parts and Kits

LPA-SMA-A
Pro-Link to SMA Adapter, new style
PK006
Probe Accessories Kit
Dx20-Cable-HiTemp
Replacement 30" matched cable set for use with Dx20 HiTemp Solder tip leadset
Dx10-Cable-HiTemp
Replacement 30" matched cable set for use with Dx10 HiTemp Solder tip leadset
OE695G-REFCAL
OE695G Reference Cal (1ch)
LPA-SMA-KIT-A
Kit of Pro-Link to SMA Adapter, new style
Dx20-SI-HiTEMP
Replacement Solder tip leadset for use with D620/D320 and temperature extension cables
Dx10-SI-HiTEMP
Replacement Solder tip leadset for use with D610/D310 and temperature extension cables

Высокоомные активные пробники

ZS1000-QUADPAK
Set of 4 ZS1000 Active Probes
ZS1500-QUADPAK
Набор из 4 пробников ZS 1500, 1,5 ГГц
ZS2500-QUADPAK
Набор из 4 пробников ZS2500, 2,5 ГГц
ZS1500
Активный пробник, 1.5 ГГц, 0,9 пФ, 1 MOм
ZS2500
Активный пробник, 2.5 ГГц, 0,9 пФ, 1 MOм
ZS4000
Активный пробник, 4.0 ГГц, 0,6 пФ, 1 MOм
ZS1000
1 GHz, 0.9 pF, 1 MOhm Active Voltage Probe

Токовые пробники

DCS025
Deskew Calibration Source for CP030, CP030A, CP031, CP031A, AP015, CP150, CP500
CP150-6M
150 A, 5 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 6 meter cable
CP030-3M
30 A, 10 MHz Current Probe - AC/DC, 30 A rms, 50 A Peak Pulse, 3 meter cable
DCS015
Deskew Calibration Source for AP015
CA10-QUADPAK
Programmable ProBus Current Adapter
CP500
Токовый пробник до 500 А, 2 МГц
CP150
Токовый пробник до 150 А, максимум 500 A < 30 мкс, 10 МГц
CP031A
Высокочувствительный токовый пробник до 30 A, 100 МГц
CP031
Токовый пробник до 30 A, 100 МГц
CP030A
Высокочувствительный токовый пробник до 30 A, 50 МГц
CP030
Токовый пробник до 30 A, 50 МГц

Дифференциальные пробники (13-25 ГГц)

D1305-A
WaveLink D1305 13 GHz/1.6Vp-p Differential Probe Amplifier with Dxx05-SI Solder-In Tip (Qty. 2)
D2505-A-CCNIST
NIST Calibration for D2505-A. Includes test data.
D2005-A-CCNIST
NIST Calibration for D2005-A. Includes test data.
D1605-A-CCNIST
NIST Calibration for D1605-A. Includes test data.
D1305-A-CCNIST
NIST Calibration for D1305-A. Includes test data.
LPA-2.92
ProLink to 2.92mm Adapter with Probe Power and Communication Pass Through
DXX05-SI
Replacement Dxx05-SI 13-25 GHz Solder-In Lead with Qty. 5 Spare Resistors. For warranted accuracy, amplifier must be returned to factory for calibration with this lead.
Dxx05-PT-KIT
WaveLink Dxx05-PT (22 GHz rating) Adjustable Positioner Tip Kit. For use with Dxx05 amplifiers.
WL-2.92MM-CASE
WaveLink 2.92mm Platform/Cable Assembly Kit for D2505-A 25 GHz WaveLink Probes.
WL-PLINK-A-CASE
WaveLink ProLink Platform/Cable Assembly Kit for Dxx05-A 13-20 GHz WaveLink Probes.
D2505-A
WaveLink D2505 25 GHz/2.4Vp-p Differential Probe Amplifier with Dxx05-SI Solder-In Tip (Qty. 2)
D2005-A
WaveLink D2005 20 GHz/2.4Vp-p Differential Probe Amplifier with Dxx05-SI Solder-In Tip (Qty. 2)
D1605-A
WaveLink D1605 16 GHz/2.4Vp-p Differential Probe Amplifier with Dxx05-SI Solder-In Tip (Qty. 2)
D2505-A-PS
25 GHz Complete Probe System with Solder-In Tip (25 GHz) and Positioner Tip Browser (22 GHz)
D2005-A-PS
20 GHz Complete Probe System with Solder-In Tip (20 GHz) and Positioner Tip Browser (20 GHz)
D1605-A-PS
16 GHz Complete Probe System with Solder-In Tip (16 GHz) and Positioner Tip Browser (16 GHz)
D1305-A-PS
13 GHz Complete Probe System with Solder-In Tip (13 GHz) and Positioner Tip Browser (13 GHz)

Пассивные пробники

PP025-1
500 MHz Passive Probe, 5mm, 10:1, 10 MOhm
PP021-1
500 MHz Passive Probe, 2.5mm, 10:1, 10 MOhm

Serial Trigger Hardware

SDA8Zi-UPG-14Gbit-80b-SYMBOL-TD
80-bit NRZ, 8b/10b and 64b/66b Serial Trigger upgrade from 6.5 Gb/s to 14.1 Gb/s for SDA 8Zi-A

Оптические и электрические преобразователи

OE555
Long wavelength O/E converter
OE695G
Optical to Electrical Converter
OE6250G-M
O-E converter, 25 GHz Bessel-Thomson response, 36 GHz flat response
OE525
Short wavelength O/E Converter (500-870 nm)
OE455
Long wavelength O/E Converter (950-1630 nm)
OE425
Short wavelength O/E Converter (500-870 nm)

Transmission Line Probes

PP066
7.5 GHz Low Capacitance ÷10/÷20 probe

Высоковольтный пробник с гальванической развязкой на основе технологии передачи аналогового сигнала через оптоволокно

HVFO-6M-FIBER
HVFO6m Optical Cable Acc'y
HVFO-2M-FIBER
HVFO 2m Optical Cable Acc'y
HVFO-1M-FIBER
HVFO 1m Optical Cable Acc'y
HVFO103-XMITTER
HVFO103 Spare Amp/Mod. Xmitter
HVFO100-40X-TIP
HVFO103 +/-40V (40x) Tip Acc'y
HVFO100-20X-TIP
HVFO103 +/-20V (20x) Tip Acc'y
HVFO100-5X-TIP
HVFO103 +/-5V (2x) Tip Acc'y
HVFO100-1X-TIP
HVFO103 +/-1V (1x) Tip Acc'y
HVFO103
High Voltage Fiber Optic Probe, 60 MHz Bandwidth. Includes soft-carrying case. Requires attenuating tip (ordered separately). Includes Qty. 1 1m Fiber Optic Cable

Высоковольтные дифференциальные пробники

ADP305
Высоковольтный дифференциальный пробник 1 кВ, 400 В, 100 MГц
ADP300
Высоковольтный дифференциальный пробник, 1 кВ, 400 В, 20 МГц
AP031
Высоковольтный дифференциальный пробник (÷10, ÷100), 700 В, 25 MГц
HVD3605А
Высоковольтный дифференциальный пробник, 6 кВ, 100 MГц с функцией автоустановки нуля
HVD3206А-6M
Высоковольтный дифференциальный пробник, 2кВ, 120 MГц с функцией автоустановки нуля
HVD3206А
Высоковольтный дифференциальный пробник, 2кВ, 120 MГц с функцией автоустановки нуля
HVD3106А-6M
Высоковольтный дифференциальный пробник с 6 метровым кабелем, 1кВ, 80 MГц с функцией автоустановки нуля
HVD3106А-NOACC
Высоковольтный дифференциальный пробник без наконечника, 1кВ, 120 MГц с функцией автоустановки нуля
HVD3106А
Высоковольтный дифференциальный пробник, 1кВ, 120 МГц с функцией автоустановки нуля
HVD3102А-NOACC
Высоковольтный дифференциальный пробник без наконечника, 1кВ, 25 МГц с функцией автоустановки нуля
HVD3102А
Высоковольтный дифференциальный пробник, 1кВ, 25 МГц с функцией автоустановки нуля

Active Voltage Rail Probes

RP4000-UFL-PCBMOUNT
Qty. 10 U.FL 3mm x 3mm PCB mounts (additional to those supplied with RP4030)
RP4000-MCX-CABLE-UFL
Qty. 3 3 GHz MCX to U.FL ultra-miniature coax cable, 8cm long (add'l to those supplied with RP4030)
RP4000-MCX-PCBMOUNT
Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, +/-30V offset, +/-800mV
RP4000-MCX-LEAD-SI
Qty. 3 MCX 4 GHz solder-in lead accessories (additional to those supplied with RP4030), 18cm long
RP4000-BROWSER
RP4030 350 MHz Browser Tip accessory. Includes 0 Ohm (1x), 450 Ohm (10x) and 950 Ohm (20x) tips.
RP4030
Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, +/-30V offset, +/-800mV

Дифференциальные усилители

DA1855A-RM
DA1855A with rackmount
DA1855A-PR2-RM
Rack mountable version of the DA1855A-PR2
DA1855A-PR2
2 Ch, 100 MHz Differential Amplifier with fast over drive recovery, calibrated offset, and selectable LP filters
DA101
10:1, 1 MOhm Passive Attenuator
DA1855A
High-performance 100 MHz Differential Amplifier

Дифференциальные пробники (8-13 ГГц)

D1330-CCNIST
NIST Calibration for D1330. Includes test data.
D1030-CCNIST
NIST Calibration for D1030. Includes test data.
D830-CCNIST
NIST Calibration for D830. Includes test data.
Dxx30-HiTemp
WaveLink Temperature Extension cables for Dxx30. Includes 1 set of matched 30 inch high temperature cables, 1 solder tip lead set.
Dxx30-QL-3SI
QuickLink Solder-In starter pack for use with Dxx30 amplifier
Dxx30-SI
Replacement Dxx30-SI 8-13 GHz Solder-In Lead with Qty. 5 Spare Resistors.
DXX30-SMA-SMP-LEADS
Lead set consisting of WaveLink Dxx30-SMA-SMP-LEADS for use with Dxx30 amplifiers.
Dxx30-PT-KIT
WaveLink Dxx30-PT (up to 10 GHz rating) Adjustable Positioner Tip Kit. For use with Dxx30 amplifiers
D1330
WaveLink D1330 13 GHz/3.5Vp-p Differential Probe Amplifier with Dxx30-SI Solder-In Tip (Qty. 2)and Dxx30-SP Square Pin (Qty. 1)
D1030
WaveLink D1030 10 GHz/3.5Vp-p Differential Probe Amplifier with Dxx30-SI Solder-In Tip (Qty. 2)and Dxx30-SP Square Pin (Qty. 1).
D830
WaveLink D830 8 GHz/3.5Vp-p Differential Probe Amplifier with Dxx30-SI Solder-In Tip (Qty. 2) andDxx30-SP Square Pin (Qty. 1)
D1330-PS
13 GHz Complete Probe System with Dxx30-SI Solder-In Tip (Qty. 2), Dxx30-SP Square Pin (Qty. 1),and Dxx30-PT-KIT Positioner Tip Browser (Qty. 1)
D1030-PS
10 GHz Complete Probe System with Dxx30-SI Solder-In Tip (Qty. 2), Dxx30-SP Square Pin (Qty. 1),and Dxx30-PT-KIT Positioner Tip Browser (Qty. 1)
D830-PS
8 GHz Complete Probe System with Dxx30-SI Solder-In Tip (Qty. 2), Dxx30-SP Square Pin (Qty. 1), and Dxx30-PT-KIT Positioner Tip Browser (Qty. 1)

Дифференциальные пробники (4-6 ГГц)

D600A-AT-CCNIST
NIST Calibration for D600A-AT. Includes test data.
D620-A-CCNIST
NIST Calibration for D620-A. Includes test data.
D610-A-CCNIST
NIST Calibration for D610-A. Includes test data.
D420-A-CCNIST
NIST Calibration for D420-A. Includes test data
D410-A-CCNIST
NIST Calibration for D410-A. Includes test data.
TF-DSQ
Probe Deskew and Calibration Test Fixture
EZ Probe
Cascade Microtech EZ-Probe Positioner
Dx20-QL-3SI
QuickLink Solder-In starter pack for use with Dx20 amplifier
Dx10-QL-3SI
QuickLink Solder-In starter pack for use with Dx10 amplifier
Dx20-SI
Replacement Solder tip lead set for D420/D620
Dx10-SI
Replacement Solder tip lead set for D410/D610
Dx20-QL
QuickLink Adapter for use with Dx20 amplifiers
Dx20-HiTemp
WaveLink Temperature Extension cables for Dx20.Includes 1 set of matched 30" high temperature cables, 1 solder tip lead se
Dx10-QL
QuickLink Adapter for use with Dx10 amplifiers
Dx10-HiTemp
WaveLink Temperature Extension cables for Dx10.Includes 1 set of matched 30" high temperature cables, 1 solder tip lead set
Dx20-PT-KIT
WaveLink Dx20-PT Adjustable Positioner Tip Kit. Includes XYZ Positioner Assembly with MechanicalInterconnects, Adhesive Kit, Connection Guides, Hand-held Wand, and Replacement Pins(Qty. 4)/Sockets(Qty. 2).
Dx10-PT-KIT
WaveLink Dx10-PT Adjustable Positioner Tip Kit. Includes XYZ Positioner Assembly with MechanicalInterconnects, Adhesive Kit, Connection Guides, Hand-held Wand, and Replacement Pins(Qty. 4)/Sockets(Qty 2).
WL-PLINK-CASE
WaveLink ProLink Platform/Cable Assembly Kit for D610, D620, D600A-AT, and Dxx30 WaveLink Probes.
WL-PBUS-CASE
WaveLink ProBus Platform/Cable Assembly Kit for D410, D420, and D300A-AT WaveLink Probes.
D600A-AT
WaveLink D600 6 GHz/4.8Vp-p Differential Amplifier Module with Adjustable Tips.
D400A-AT
WaveLink D400 4 GHz/4.8Vp-p Differential Amplifier Module with Adjustable Tips
D620-A
WaveLink D620-A 6 GHz/5Vp-p and +/-3V Offset Range Differential Amplifier Small Tip Module with Sold Small Tip Module with Solder-in, Quick Connect, and Square Pin Lead Sets, plus accessories.
D610-A
WaveLink D610-A 6 GHz/2.5Vp-p and +/-3V Offset Range Differential Amplifier Small Tip Module with So Small Tip Module with Solder-in, Quick Connect, and Square Pin Lead Sets, plus accessories.
D420-A
WaveLink D420-A 4 GHz/5Vp-p and +/-3V Offset Range Differential Amplifier Small Tip Module with Sold Small Tip Module with Solder-in, Quick Connect, and Square Pin Lead Sets, plus accessories.
D410-A
WaveLink D410-A 4 GHz/2.5Vp-p and +/-3V Offset Range Differential Amplifier Small Tip Module with So Small Tip Module with Solder-in, Quick Connect, and Square Pin Lead Sets, plus accessories.
D610-A-PS
6 GHz Complete Probe System with Dx10-SI Solder-In Tip (Qty. 1), Dx10-QC Quick Connect (Qty. 1), Dx10-SP Square Pin (Qty. 1), and Dx10-PT-KIT Positioner Tip Browser (Qty. 1)
D420-A-PS
4 GHz Complete Probe System with Dx20-SI Solder-In Tip (Qty. 1), Dx20-QC Quick Connect (Qty. 1), Dx20-SP Square Pin (Qty. 1), and Dx20-PT-KIT Positioner Tip Browser (Qty. 1)
D410-A-PB2
4 GHz ProBus2 Differential Probe with Dx10-SI Solder-In Tip (Qty. 1), Dx10-QC Quick Connect (Qty. 1) and Dx10-SP Square Pin (Qty. 1)

Высоковольтные пассивные пробники

PPE6KV
Высоковольтный пробник , 1000:1 400 МГц, 5 MOм/50 MOм
PPE5KV
Высоковольтный пробник , 100:1 400 MГц 50 MOм
PPE4KV
Высоковольтный пробник ,100:1 400 МГц , 50 MOм
HVP120
Высоковольтный пассивный пробник 1 Вскз , 400 МГц

Дифференциальные пробники (<= 1.5 ГГц)

ZD500
Активный дифференциальный пробник 500 MГц, 1,0 пФ, ±8 V
ZD200
Активный дифференциальный пробник, 200 МГц, 3,5 пФ, 1 МОм, ±20 В
ZD1500
Активный дифференциальный пробник, 1,5 ГГц, 1.0 пФ, ±8 V
ZD1000
Активный дифференциальный пробник, 1 ГГц, 1,0 пФ, ±8 В
AP033
Дифференциальный пробник до 500 МГц

Адаптер для пробников

CA10
Programmable ProBus Current Adapter
TPA10-QUADPAK
Set of 4 TPA10 ProBus Probe Adapters
TPA10
ProBus Probe Adapter for TekProbe-BNC Probes
Цена: по запросу руб.
Поверка 20 000 руб.
Гарантия 36 месяцев
Госреестр № 64557-16 до: 11.07.21 г.